|
Naslov: mandriva 2008 , problem sa mreznom karticom! Poruka od: zchira 24 Новембар 2007, 00:26:50 Nabacio sam novi hard i instalirao mandrivu2008
( http://www.linuxo.net/component/option,com_smf/Itemid,82/topic,8434.0/ ) Sve je proslo lepo, osim sto nemam net (adsl). Podesio sam sve kao na staroj mandrivi 2007 (iz nje sad pishem ovo) Uneo sam paramentre (ip, gateway, dns, netmask) i jednostavno ne radi. ifconfig mi izbacuje samo loopback (127.0.0.1) a nema eth0. Inace, ploca mi je K8NS-pro, nForce3, sa integrisanom mreznom kariticom (sysconnect valjda) jel ima neko neki predlog? Naslov: Odg: mandriva 2008 , problem sa mreznom karticom! Poruka od: dukenukem_4d 24 Новембар 2007, 01:22:04 nije prepoznao drajver,uradi mu lsmod na 2007
pa onda i na 2008 jel nisi pre to isto podesavao na slack? (tj da li ti je isti komp) (gledao sam ove mrezne teme malo ranije ,ne secam se tacno gde bese) e ako 'oces da isprobas ovaj actiontec, stvarno dobro radi ,sad pisem iz njega nego nesto izgleda nisu ljudi bas zainteresovani ,mislim nisu mnogo :'( (salim se...) ili ako je ipak prepoznao a nije podignut ifconfig -a prikazuje one mrezne interfejse koji su down (ali trebao bi da ga automatski podigne) ovo mirise na neki hal problem opet? Naslov: Odg: mandriva 2008 , problem sa mreznom karticom! Poruka od: zchira 24 Новембар 2007, 10:59:08 U pravu si, isti problem sam imao i na slacku (10.2 ili 11.). I resio sam ga tako sto sam kucao
modprobe sklin98 (ili modprobe sk98lin , ne secam se tacno. U pitanju je isti kompjuter. Inace, evo izlaza komande lsmod na 2007: [root@zmandiva zchira]# lsmod Module Size Used by appletalk 32812 2 ipx 25860 2 p8023 2368 1 ipx ipv6 237120 14 skge 33456 0 snd_seq_dummy 3620 0 snd_seq_oss 31392 0 snd_seq_midi_event 7072 1 snd_seq_oss snd_seq 49488 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi_event snd_seq_device 7212 3 snd_seq_dummy,snd_seq_oss,snd_seq snd_pcm_oss 40384 0 snd_mixer_oss 16096 1 snd_pcm_oss af_packet 17960 0 snd_intel8x0 29372 2 snd_ac97_codec 96868 1 snd_intel8x0 snd_ac97_bus 2848 1 snd_ac97_codec snd_pcm 70116 3 snd_pcm_oss,snd_intel8x0,snd_ac97_codec snd_timer 19620 2 snd_seq,snd_pcm snd_page_alloc 8712 2 snd_intel8x0,snd_pcm snd 46500 13 snd_seq_oss,snd_seq,snd_seq_device,snd_pcm_oss,snd_mixer_oss,snd_intel8x0,snd_ac97_codec,snd_pcm,snd_timer soundcore 8096 1 snd video 13924 0 thermal 11240 0 processor 21448 1 thermal fan 4036 0 container 3968 0 button 5808 0 battery 8260 0 ac 4292 0 ide_cd 35776 0 binfmt_misc 9800 1 loop 15400 0 nls_cp437 6464 1 vfat 11104 1 fat 46876 1 vfat nls_utf8 2624 2 ntfs 266940 1 sg 30776 0 sata_sil 7784 0 sd_mod 18560 0 sata_nv 7556 0 libata 60940 2 sata_sil,sata_nv scsi_mod 119016 3 sg,sd_mod,libata dm_mod 49944 0 amd64_agp 10948 1 nvidia 6830612 22 agpgart 27240 2 amd64_agp,nvidia i2c_core 17536 1 nvidia evdev 8864 1 tsdev 7040 0 usbmouse 5280 0 usbhid 49024 0 ehci_hcd 29160 0 ohci_hcd 19012 0 usbcore 113472 5 usbmouse,usbhid,ehci_hcd,ohci_hcd ext3 124936 1 jbd 51028 1 ext3 _____________ pretpostavljam da je ono skge modul za mreznu... sad idem na 2008, da vidim sta ce tamo da mi izbaci... Naslov: Odg: mandriva 2008 , problem sa mreznom karticom! Poruka od: zchira 24 Новембар 2007, 11:31:34 evo i lsmod iz 2008-ice:
[root@zmandriva zchira]# lsmod Module Size Used by nvidia 6213552 34 tun 8800 0 af_packet 17960 0 snd_seq_dummy 3492 0 ipv6 250084 12 snd_seq_oss 29888 0 snd_seq_midi_event 6912 1 snd_seq_oss snd_seq 46800 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi_event snd_seq_device 7276 3 snd_seq_dummy,snd_seq_oss,snd_seq snd_pcm_oss 37216 0 snd_mixer_oss 14784 1 snd_pcm_oss video 15080 0 thermal 11304 0 sbs 16520 0 fan 4260 0 container 4032 0 button 6576 0 dock 7600 0 battery 10344 0 ac 4452 0 binfmt_misc 9416 1 loop 14276 0 nls_cp437 6304 3 vfat 11040 3 fat 45852 1 vfat nls_utf8 2496 4 ntfs 252840 1 ide_cd 35200 0 dm_mirror 20224 0 dm_mod 48064 1 dm_mirror ide_disk 14624 4 amd74xx 14300 0 [permanent] usb_storage 90276 0 ide_core 99748 4 ide_cd,ide_disk,amd74xx,usb_storage sata_sil 8648 0 cpufreq_ondemand 7340 1 cpufreq_conservative 6600 0 cpufreq_powersave 2240 0 powernow_k8 14336 0 freq_table 4512 2 cpufreq_ondemand,powernow_k8 processor 25796 2 thermal,powernow_k8 tsdev 7104 0 usbmouse 4832 0 usbhid 38880 0 ff_memless 5448 1 usbhid skge 36336 0 snd_intel8x0 29404 3 snd_ac97_codec 96836 1 snd_intel8x0 shpchp 29812 0 ohci_hcd 19972 0 ehci_hcd 30668 0 pci_hotplug 27360 1 shpchp ac97_bus 2752 1 snd_ac97_codec usbcore 113576 6 usb_storage,usbmouse,usbhid,ohci_hcd,ehci_hcd snd_pcm 69636 4 snd_pcm_oss,snd_intel8x0,snd_ac97_codec i2c_nforce2 5728 0 i2c_core 20224 2 nvidia,i2c_nforce2 k8temp 5120 0 amd64_agp 10180 1 snd_timer 19652 3 snd_seq,snd_pcm agpgart 27656 2 nvidia,amd64_agp snd 45092 13 snd_seq_oss,snd_seq,snd_seq_device,snd_pcm_oss,snd_mixer_oss,snd_intel8x0,snd_ac97_codec,snd_pcm,snd_timer soundcore 6624 1 snd snd_page_alloc 8456 2 snd_intel8x0,snd_pcm evdev 8448 3 sg 30552 0 ext3 117896 1 jbd 50312 1 ext3 scsi_wait_scan 1920 0 sd_mod 26240 5 sata_nv 15844 4 libata 108688 2 sata_sil,sata_nv scsi_mod 124972 5 usb_storage,sg,scsi_wait_scan,sd_mod,libata [root@zmandriva zchira]# evi i ifconfig iz 2008: [root@zmandriva etc]# ifconfig lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:384 errors:0 dropped:0 overruns:0 frame:0 TX packets:384 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:29424 (28.7 KiB) TX bytes:29424 (28.7 KiB) Naslov: Odg: mandriva 2008 , problem sa mreznom karticom! Poruka od: kmilos 24 Новембар 2007, 13:02:50 ifconfig ti prikazuje samo podešene i podignute mrežne sprege, što ne znači da mrežna kartica nije prepoznata - kao što vidiš drajver je učitan. Pročešljaj dmesg izlaz i /proc/net/dev kako bi potvrdio da eth0 stvarno postoji.
Naslov: Odg: mandriva 2008 , problem sa mreznom karticom! Poruka od: zchira 24 Новембар 2007, 13:32:47 ok. Evo izlaza
Citat [zchira@zmandriva ~]$ dmesg Linux version 2.6.22.9-desktop-1mdv (lcapitulino@n5.mandriva.com) (gcc version 4.2.2 20070909 (prerelease) (4.2.2-0.RC.1mdv2008.0)) #1 SMP Thu Sep 27 04:07:04 CEST 2007 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009f800 (usable) BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001fff0000 (usable) BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS) BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data) BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) 0MB HIGHMEM available. 511MB LOWMEM available. found SMP MP-table at 000f5100 Entering add_active_range(0, 0, 131056) 0 entries of 256 used Zone PFN ranges: DMA 0 -> 4096 Normal 4096 -> 131056 HighMem 131056 -> 131056 early_node_map[1] active PFN ranges 0: 0 -> 131056 On node 0 totalpages: 131056 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 991 pages used for memmap Normal zone: 125969 pages, LIFO batch:31 HighMem zone: 0 pages used for memmap DMI 2.3 present. ACPI: RSDP 000F6CB0, 0014 (r0 Nvidia) ACPI: RSDT 1FFF3000, 002C (r1 Nvidia AWRDACPI 42302E31 AWRD 1010101) ACPI: FACP 1FFF3040, 0074 (r1 Nvidia AWRDACPI 42302E31 AWRD 1010101) ACPI: DSDT 1FFF30C0, 48AA (r1 NVIDIA AWRDACPI 1000 MSFT 100000C) ACPI: FACS 1FFF0000, 0040 ACPI: APIC 1FFF7980, 005A (r1 Nvidia AWRDACPI 42302E31 AWRD 1010101) Nvidia board detected. Ignoring ACPI timer override. If you got timer trouble try acpi_use_timer_override ACPI: PM-Timer IO Port: 0x1008 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 15:12 APIC version 16 ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1]) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: BIOS IRQ0 pin2 override ignored. ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: IRQ9 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 30000000 (gap: 20000000:dec00000) swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000 swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000f0000 swsusp: Registered nosave memory region: 00000000000f0000 - 0000000000100000 Built 1 zonelists. Total pages: 130033 Kernel command line: BOOT_IMAGE=linux root=/dev/sda1 resume=/dev/sda2 splash=silent vga=788 bootsplash: silent mode. mapped APIC to ffffd000 (fee00000) mapped IOAPIC to ffffc000 (fec00000) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 2048 (order: 11, 8192 bytes) Detected 1872.198 MHz processor. spurious 8259A interrupt: IRQ7. Console: colour dummy device 80x25 Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 514120k/524224k available (2139k kernel code, 9052k reserved, 691k data, 280k init, 0k highmem, 0k BadRAM) virtual kernel memory layout: fixmap : 0xffe16000 - 0xfffff000 (1956 kB) pkmap : 0xff800000 - 0xffc00000 (4096 kB) vmalloc : 0xe0800000 - 0xff7fe000 ( 495 MB) lowmem : 0xc0000000 - 0xdfff0000 ( 511 MB) .init : 0xc03ca000 - 0xc0410000 ( 280 kB) .data : 0xc0316d67 - 0xc03c3c84 ( 691 kB) .text : 0xc0100000 - 0xc0316d67 (2139 kB) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 3745.54 BogoMIPS (lpj=1872771) Security Framework v1.0.0 initialized Mount-cache hash table entries: 512 CPU: After generic identify, caps: 078bfbff e1d3fbff 00000000 00000000 00000000 00000000 00000000 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 512K (64 bytes/line) CPU: After all inits, caps: 078bfbff e1d3fbff 00000000 00000410 00000000 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. Compat vDSO mapped to ffffe000. Checking 'hlt' instruction... OK. SMP alternatives: switching to UP code Freeing SMP alternatives: 12k freed Early unpacking initramfs... done Freeing initrd memory: 924k freed ACPI: Core revision 20070126 ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found. CPU0: AMD Athlon(tm) 64 Processor 2800+ stepping 00 Total of 1 processors activated (3745.54 BogoMIPS). ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1 Brought up 1 CPUs Booting paravirtualized kernel on bare hardware NET: Registered protocol family 16 ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xfb730, last bus=2 PCI: Using configuration type 1 Setting up standard PCI resources ACPI: EC: Look up EC in DSDT ACPI: Interpreter enabled ACPI: (supports S0 S1 S4 S5) ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 6 7 9 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 *5 6 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 6 7 *9 10 11 12 14 15) ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 5 6 7 9 *10 11 12 14 15) ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 6 7 9 *10 11 12 14 15) ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LAPU] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 *5 6 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 5 6 7 9 *10 11 12 14 15) ACPI: PCI Interrupt Link [LFIR] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [L3CM] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LSID] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LFID] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) ACPI: PCI Interrupt Link [APC1] (IRQs *16), disabled. ACPI: PCI Interrupt Link [APC2] (IRQs *17) ACPI: PCI Interrupt Link [APC3] (IRQs *18), disabled. ACPI: PCI Interrupt Link [APC4] (IRQs *19) ACPI: PCI Interrupt Link [APC5] (IRQs *16) ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22) *0 ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22) *0 ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22) *0, disabled. ACPI: PCI Interrupt Link [APCI] (IRQs 20 21 22) *0, disabled. ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22) *0 ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22) *0, disabled. ACPI: PCI Interrupt Link [APCS] (IRQs *23) ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22) *0 ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22) *0, disabled. ACPI: PCI Interrupt Link [AP3C] (IRQs 20 21 22) *0, disabled. ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22) *0, disabled. ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22) *0, disabled. ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22) *0 ACPI: Power Resource [ISAV] (on) Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init ACPI: bus type pnp registered pnp: PnP ACPI: found 13 devices ACPI: ACPI bus type pnp unregistered PnPBIOS: Disabled PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report ACPI: RTC can wake from S4 pnp: 00:00: ioport range 0x1000-0x107f has been reserved pnp: 00:00: ioport range 0x1080-0x10ff has been reserved pnp: 00:00: ioport range 0x1400-0x147f has been reserved pnp: 00:00: ioport range 0x1480-0x14ff has been reserved pnp: 00:00: ioport range 0x1800-0x187f has been reserved pnp: 00:00: ioport range 0x1880-0x18ff has been reserved pnp: 00:01: iomem range 0xf0000-0xf3fff could not be reserved pnp: 00:01: iomem range 0xf4000-0xf7fff could not be reserved pnp: 00:01: iomem range 0xf8000-0xfbfff could not be reserved pnp: 00:01: iomem range 0xfc000-0xfffff could not be reserved Time: tsc clocksource has been installed. PCI: Bridge: 0000:00:0b.0 IO window: disabled. MEM window: f8000000-f9ffffff PREFETCH window: e0000000-efffffff PCI: Bridge: 0000:00:0e.0 IO window: 9000-afff MEM window: fa000000-fbffffff PREFETCH window: 30000000-300fffff PCI: Setting latency timer of device 0000:00:0e.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 4096 (order: 2, 16384 bytes) TCP established hash table entries: 16384 (order: 5, 196608 bytes) TCP bind hash table entries: 16384 (order: 5, 131072 bytes) TCP: Hash tables configured (established 16384 bind 16384) TCP reno registered apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac) apm: overridden by ACPI. audit: initializing netlink socket (disabled) audit(1195906687.227:1): initialized Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) Boot video device is 0000:01:00.0 vesafb: framebuffer at 0xe0000000, mapped to 0xe0880000, using 3750k, total 131072k vesafb: mode is 800x600x16, linelength=1600, pages=2 vesafb: protected mode interface info at c000:e6d0 vesafb: pmi: set display start = c00ce706, set palette = c00ce770 vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da vesafb: scrolling: redraw vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 222382 bytes,<6>...found (800x600, 222334 bytes, v3). Console: switching to colour frame buffer device 93x31 fb0: VESA VGA frame buffer device isapnp: Scanning for PnP cards... Switched to high resolution mode on CPU 0 isapnp: No Plug & Play device found Generic RTC Driver v1.07 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1 PNP: PS/2 controller doesn't have AUX irq; using default 12 serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice input: AT Translated Set 2 keyboard as /class/input/input0 TCP cubic registered NET: Registered protocol family 1 Using IPI No-Shortcut mode BIOS EDD facility v0.16 2004-Jun-25, 6 devices found Freeing unused kernel memory: 280k freed SCSI subsystem initialized libata version 2.21 loaded. sata_nv 0000:00:0a.0: version 3.4 ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 22 ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [APSJ] -> GSI 22 (level, high) -> IRQ 16 PCI: Setting latency timer of device 0000:00:0a.0 to 64 scsi0 : sata_nv scsi1 : sata_nv ata1: SATA max UDMA/133 cmd 0x000109f0 ctl 0x00010bf2 bmdma 0x0001dc00 irq 16 ata2: SATA max UDMA/133 cmd 0x00010970 ctl 0x00010b72 bmdma 0x0001dc08 irq 16 ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata1.00: ATA-7: ST3250410AS, 3.AAC, max UDMA/133 ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 0/32) ata1.00: configured for UDMA/133 ata2: SATA link down (SStatus 0 SControl 300) scsi 0:0:0:0: Direct-Access ATA ST3250410AS 3.AA PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 < sda5 sda6 > sd 0:0:0:0: [sda] Attached SCSI disk swsusp: Marking nosave pages: 000000000009f000 - 0000000000100000 swsusp: Basic memory bitmaps created swsusp: Basic memory bitmaps freed kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. sd 0:0:0:0: Attached scsi generic sg0 type 0 Linux agpgart interface v0.102 (c) Dave Jones agpgart: Detected AGP bridge 0 agpgart: Setting up Nforce3 AGP. agpgart: AGP aperture is 128M @ 0xf0000000 i2c-adapter i2c-0: nForce2 SMBus adapter at 0x1c00 i2c-adapter i2c-1: nForce2 SMBus adapter at 0x2000 pci_hotplug: PCI Hot Plug PCI Core version: 0.5 usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 ACPI: PCI Interrupt Link [APCL] enabled at IRQ 21 ACPI: PCI Interrupt 0000:00:02.2[C] -> Link [APCL] -> GSI 21 (level, high) -> IRQ 17 PCI: Setting latency timer of device 0000:00:02.2 to 64 ehci_hcd 0000:00:02.2: EHCI Host Controller ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:02.2: debug port 1 PCI: cache line size of 64 is not supported by device 0000:00:02.2 ehci_hcd 0000:00:02.2: irq 17, io mem 0xfc005000 ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 8 ports detected ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 20 ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [APCJ] -> GSI 20 (level, high) -> IRQ 18 PCI: Setting latency timer of device 0000:00:06.0 to 64 intel8x0_measure_ac97_clock: measured 50724 usecs intel8x0: clocking to 46822 ACPI: PCI Interrupt Link [APCF] enabled at IRQ 22 ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 22 (level, high) -> IRQ 16 PCI: Setting latency timer of device 0000:00:02.0 to 64 ohci_hcd 0000:00:02.0: OHCI Host Controller ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:02.0: irq 16, io mem 0xfc003000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 4 ports detected ACPI: PCI Interrupt Link [APCG] enabled at IRQ 21 ACPI: PCI Interrupt 0000:00:02.1 -> Link [APCG] -> GSI 21 (level, high) -> IRQ 17 PCI: Setting latency timer of device 0000:00:02.1 to 64 ohci_hcd 0000:00:02.1: OHCI Host Controller ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 3 ohci_hcd 0000:00:02.1: irq 17, io mem 0xfc004000 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 4 ports detected ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19 ACPI: PCI Interrupt 0000:02:0b.0[A] -> Link [APC4] -> GSI 19 (level, low) -> IRQ 19 skge 1.11 addr 0xfb000000 irq 19 chip Yukon-Lite rev 7 skge 0000:02:0b.0: bad (zero?) ethernet address in rom skge eth0: addr 00:00:00:00:00:00 usb 2-4: new low speed USB device using ohci_hcd and address 2 usb 2-4: configuration #1 chosen from 1 choice usbcore: registered new interface driver hiddev input: Logitech USB-PS/2 Optical Mouse as /class/input/input1 input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:02.0-4 usbcore: registered new interface driver usbhid drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver usbcore: registered new interface driver usbmouse drivers/hid/usbhid/usbmouse.c: v1.6:USB HID Boot Protocol mouse driver powernow-k8: Found 1 AMD Athlon(tm) 64 Processor 2800+ processors (version 2.00.00) powernow-k8: 0 : fid 0xa (1800 MHz), vid 0x2 powernow-k8: 1 : fid 0x2 (1000 MHz), vid 0x12 floppy0: no floppy controllers found sata_sil 0000:02:0d.0: version 2.2 ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17 ACPI: PCI Interrupt 0000:02:0d.0[A] -> Link [APC2] -> GSI 17 (level, low) -> IRQ 20 scsi2 : sata_sil scsi3 : sata_sil ata3: SATA max UDMA/100 cmd 0xe0ea4080 ctl 0xe0ea408a bmdma 0xe0ea4000 irq 20 ata4: SATA max UDMA/100 cmd 0xe0ea40c0 ctl 0xe0ea40ca bmdma 0xe0ea4008 irq 20 ata3: SATA link down (SStatus 0 SControl 310) ata4: SATA link down (SStatus 0 SControl 310) Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. NFORCE3-250: IDE controller at PCI slot 0000:00:08.0 NFORCE3-250: chipset revision 162 NFORCE3-250: not 100% native mode: will probe irqs later NFORCE3-250: BIOS didn't set cable bits correctly. Enabling workaround. NFORCE3-250: BIOS didn't set cable bits correctly. Enabling workaround. NFORCE3-250: 0000:00:08.0 (rev a2) UDMA133 controller ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA Probing IDE interface ide0... hda: ST380011A, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... hda: max request size: 512KiB hda: Host Protected Area detected. current capacity is 156299375 sectors (80025 MB) native capacity is 156301488 sectors (80026 MB) hda: Host Protected Area disabled. hda: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100) hda: cache flushes supported hda: hda1 hda2 < hda5 hda6 > hda3 hdc: PIONEER DVD-RW DVR-108, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com hdc: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache, UDMA(66) Uniform CD-ROM driver Revision: 3.20 EXT3 FS on sda1, internal journal Adding 1020088k swap on /dev/hda5. Priority:-1 extents:1 across:1020088k Adding 1052252k swap on /dev/sda2. Priority:-2 extents:1 across:1052252k NTFS driver 2.1.28 [Flags: R/O DEBUG MODULE]. NTFS volume version 3.1. FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive! FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive! FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive! loop: module loaded bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 222382 bytes,<6>...found (800x600, 222334 bytes, v3). bootsplash: status on console 0 changed to on Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (4095 buckets, 32760 max) No dock devices found. Removing netfilter NETLINK layer. input: Power Button (FF) as /class/input/input2 ACPI: Power Button (FF) [PWRF] input: Power Button (CM) as /class/input/input3 ACPI: Power Button (CM) [PWRB] NET: Registered protocol family 10 lo: Disabled Privacy Extensions Mobile IPv6 NET: Registered protocol family 17 tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> nvidia: module license 'NVIDIA' taints kernel. ACPI: PCI Interrupt Link [APC5] enabled at IRQ 16 ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [APC5] -> GSI 16 (level, low) -> IRQ 21 NVRM: loading NVIDIA UNIX x86 Kernel Module 100.14.19 Wed Sep 12 14:12:24 PDT 2007 agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0. agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 14966 bytes, v3). bootsplash: status on console 0 changed to on bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 14966 bytes, v3). bootsplash: status on console 1 changed to on bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 14966 bytes, v3). bootsplash: status on console 2 changed to on bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 14966 bytes, v3). bootsplash: status on console 3 changed to on bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 14966 bytes, v3). bootsplash: status on console 4 changed to on bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 14966 bytes, v3). bootsplash: status on console 5 changed to on Marking TSC unstable due to: cpufreq changes. Time: acpi_pm clocksource has been installed. Clocksource tsc unstable (delta = -67080171 ns) [zchira@zmandriva ~]$ i /prov/net/dev: Citat [zchira@zmandriva net]$ cat dev Inter-| Receive | Transmit face |bytes packets errs drop fifo frame compressed multicast|bytes packets errs drop fifo colls carrier compressed lo: 1808 24 0 0 0 0 0 0 1808 24 0 0 0 0 0 0 eth0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 [zchira@zmandriva net]$ Naslov: Odg: mandriva 2008 , problem sa mreznom karticom! Poruka od: kmilos 24 Новембар 2007, 14:11:47 Znači, kao što rekoh, hardver jeste prepoznat i eth0 sprega postoji na sistemu, samo treba da je podesiš i podigneš, tj. omogućiš. Mandrivine gui alate ne poznajem, ali bi trebalo da je jednsotavno to odraditi.
Naslov: Odg: mandriva 2008 , problem sa mreznom karticom! Poruka od: zchira 24 Новембар 2007, 14:28:20 Pokusavao sam nesto ali nisam uspeo.
Inace na 2008ci stoji: Citat skge 1.11 addr 0xfb000000 irq 19 chip Yukon-Lite rev 7 skge 0000:02:0b.0: bad (zero?) ethernet address in rom skge eth0: addr 00:00:00:00:00:00 a na 2007: Citat skge 1.5 addr 0xfb000000 irq 21 chip Yukon-Lite rev 7 skge eth0: addr 00:00:00:00:00:00 skge eth0: enabling interface skge eth0: Link is up at 100 Mbps, full duplex, flow control none Naslov: Odg: mandriva 2008 , problem sa mreznom karticom! Poruka od: sasa_stole 24 Новембар 2007, 17:54:34 Jesi li napravio adsl konekciju u MMC-u? Ako nisi, neće ti raditi. Na 2007-ici mi se dešavalo da kad mi se resetuje ruter-modem da sam morao ponovo da pravim net konekciju. Pokreni MMC, uđi u Network i napravi novu LAN konekciju, zatim izaberi Ethernet i podesi kako već tebi treba. Javi da li je prošlo
Naslov: Odg: mandriva 2008 , problem sa mreznom karticom! Poruka od: zchira 24 Новембар 2007, 18:06:15 Isao sam u Control Centar, pa na 'network&internet' , pa na 'set up a new network interface'
pa sam izabrao ethernet. tu sam mogao da biram DHCP i manual. Izabrao sam manual i uneo podatke koje sam dobio od provajdera (na isti nacin sam podesio i u mandrivi 2007). na kraju mi ispise 'congratulations bla bla ...", ali net i dalje ne radi... Naslov: Odg: mandriva 2008 , problem sa mreznom karticom! Poruka od: zchira 24 Новембар 2007, 19:12:56 evo jos nekih izlaza iz konzole:
Citat [root@zmandriva zchira]# ifconfig -a eth0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) Interrupt:19 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:152 errors:0 dropped:0 overruns:0 frame:0 TX packets:152 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:11488 (11.2 KiB) TX bytes:11488 (11.2 KiB) Citat [root@zmandriva zchira]# ifconfig eth0 up SIOCSIFFLAGS: Invalid argument Naslov: Odg: mandriva 2008 , problem sa mreznom karticom! Poruka od: dukenukem_4d 24 Новембар 2007, 19:47:24 ovo mu kaze u source za skge 1.11
Kod: 3710 /* Some motherboards are broken and has zero in ROM. */ http://lxr.linux.no/source/drivers/net/skge.c3711 if (!is_valid_ether_addr(dev->dev_addr)) 3712 dev_warn(&pdev->dev, "bad (zero?) ethernet address in rom\n"); 3713 3714 err = register_netdev(dev); 3715 if (err) { 3716 dev_err(&pdev->dev, "cannot register net device\n"); 3717 goto err_out_free_netdev; 3718 } 3719 3720 err = request_irq(pdev->irq, skge_intr, IRQF_SHARED, dev->name, hw); 3721 if (err) { 3722 dev_err(&pdev->dev, "%s: cannot assign irq %d\n", 3723 dev->name, pdev->irq); 3724 goto err_out_unregister; 3725 } 3726 skge_show_addr(dev); 3727 3728 if (hw->ports > 1 && (dev1 = skge_devinit(hw, 1, using_dac))) { 3729 if (register_netdev(dev1) == 0) 3730 skge_show_addr(dev1); 3731 else { 3732 /* Failure to register second port need not be fatal */ 3733 dev_warn(&pdev->dev, "register of second port failed\n"); 3734 hw->dev[1] = NULL; 3735 free_netdev(dev1); 3736 } 3737 } 3738 pci_set_drvdata(pdev, hw); 3739 3740 return 0; 3741 da se ne buni na 2008-ci zato sto mu je hw adresa 00:00:00:00:00:00 probaj ako hoce da mu se promeni ta adresa nekako.. da li mozes iz 2007-ce da procitas iz rutera koja mu je prava hw-adresa ? pa onda(ovo dok je interfejs down) ifconfig eth0 hw ether 00:xx:yy:zz:qq:ww posle toga bi trebao da ga preuzme dhcclient automatski ili za ove xx yy zz qq ww nest0 izmisli ? [0-9] [a-f] hexadecimalno Naslov: Odg: mandriva 2008 , problem sa mreznom karticom! Poruka od: zchira 24 Новембар 2007, 20:27:40 uf. ne znam koliko sam razumeo.
Na 2007-ici mi je isto adresa 00:00:00 evo ifconfiga iz 2007: Citat eth0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 S tim, sto u 2007 redi normalno.inet addr:192.168.1.20 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::200:ff:fe00:0/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2467 errors:0 dropped:0 overruns:0 frame:0 TX packets:2033 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2558185 (2.4 MiB) TX bytes:497263 (485.6 KiB) Interrupt:21 Sto se tice rutera, logovao sam se na njega (iz 2007) sa 192.168.1.1 i tamo nasao ova podatke: Product Information Model Number AR7RD USB PID 0x6060 USB VID 0x0451 Ethernet MAC 00:11:D8:AD:2C:27 USB MAC 0A:11:D8:AD:2C:27 USB Host MAC 02:11:D8:AD:2C:27 Software Versions Gateway 3.6.0C_3A00 ATM Driver 4.05.07.00 DSL HAL 4.00.02.00 DSL Datapump 4.00.02.00 Annex A SAR HAL 01.07.2a PDSP Firmware 0.50 Boot Loader 1.2.1.5 Ove MAC adrese se odnose (pretpostavljam) na ruter a ne na moju mreznu karticu u racunaru... Citat pa onda(ovo dok je interfejs down) ifconfig eth0 hw ether 00:xx:yy:zz:qq:ww posle toga bi trebao da ga preuzme dhcclient automatski ili za ove xx yy zz qq ww nest0 izmisli ? [0-9] [a-f] hexadecimalno Jel mozes malo da mi pojasnis :-\ sta da uradim. Jel ovo treba iz 2008-ice da probam (verovatno glupo pitanje :-) )? Naslov: Odg: mandriva 2008 , problem sa mreznom karticom! Poruka od: dukenukem_4d 24 Новембар 2007, 20:45:18 jel je to ovaj ruter utstarcom?(ovo je jedini link sto sam nasao,iako nije vezano za temu)
http://portforward.com/english/routers/port_forwarding/UTStarcom/AR7RD/BitTorrent.htm trebalo bi negde da ima 'learned MAC table' ili tako nesto to je spisak ovih mac adresa (ili hardverskih adresa) svih mreznih kartica koje su trenutno prikacene na taj ruter (u tvom slucaju je samo jedna mrezna) ovi mac-ovi 00:11:D8:aa:bb:cc su izgleda od rutera,ne od mrezne znaci iz 2007-mice procitas na ruteru koji je MAC(pomocu web-interfejsa) i uneses ga u 2008-micu e, a jel si kacio ovo neki put na usb-port na linuxu? moze da se desi da proradi pomocu cdc_ether drajvera (on je za veliki broj usb network adaptera ako su po tom standardu/specifikaciji ,valjda tako nesto bese) Naslov: Odg: mandriva 2008 , problem sa mreznom karticom! Poruka od: zchira 24 Новембар 2007, 21:02:39 ruter mi je neki asus (ali interfejs izgleda kao na ovom sajtu) i na njemu nigde nisam mogao da nadjem MAC adresu moje mrezne kartice.. jedino sto sam nasao je bilo:
Static Addresses Delete IP Address Hostname MAC Type 192.168.1.20 zzz 00:00:00:00:00:00 Static Naslov: Odg: mandriva 2008 , problem sa mreznom karticom! Poruka od: dukenukem_4d 24 Новембар 2007, 21:15:31 ne znam.. izgleda da je stvarno 00:00:00:00:00:00 ???
probaj da stavis neku izmisljenu mac adresu ,ili probaj ga na usb utakni ga na usb,a izvuci mrezni kabli , i onda ako se ne pojavi novi mrezni interfejs ucitaj mu cdc_ether modprobe cdc_ether pa onda ovo ostalo ifconfig itd. (iskopao sam da kao radi na usb ,odavde ,dugacko http://www.archlinux.org/pipermail/arch/2006-October.txt.gz ) *u prilogu,izvuceno Naslov: Odg: mandriva 2008 , problem sa mreznom karticom! Poruka od: zchira 24 Новембар 2007, 21:34:27 pre nego odem u 2008-icu da probam, sta mislis o ovom:
ovo su delovi dmesg izlaza koji se ticu skge-a --- 2008 skge 1.11 addr 0xfb000000 irq 19 chip Yukon-Lite rev 7 skge 0000:02:0b.0: bad (zero?) ethernet address in rom skge eth0: addr 00:00:00:00:00:00 2007 skge 1.5 addr 0xfb000000 irq 21 chip Yukon-Lite rev 7 skge eth0: addr 00:00:00:00:00:00 skge eth0: enabling interface skge eth0: Link is up at 100 Mbps, full duplex, flow control none razlicite verzije modula skge. Jel mogu da iskopiram modul iz 2007 u 2008 , bez da kompajliram kernel ili nesto slicno. Dakle samo kopi-paste :-) Naslov: Odg: mandriva 2008 , problem sa mreznom karticom! Poruka od: dukenukem_4d 24 Новембар 2007, 21:56:14 mislim da ne ,jer moraju da im se poklope verzije kernela kao i verzija gcc
(na modinfo se vidi da je razlicito ,u vermagic polju) ali moze da se ukompilira skge 1.5 iz sorsa njegovog ,ali na ovom novijem kernelu za 2008 (ako ne prijavi neku gresku u procesu ,jer je noviji kernel) na 2007 je 2.6.17 valjda,verovano ce da prijavi dosta 'errors' kada se radi make na ovom novijem za 2008 ili ako nije do modula uopste,vec posle kad sistem preuzme interfejs? kako to da se utvrdi? Naslov: Odg: mandriva 2008 , problem sa mreznom karticom! Poruka od: zchira 24 Новембар 2007, 22:27:25 postaje komplikovano... ne mogu da verujem da neki najnoviji linux ima ovakve probleme... cak ni slackware od pre vise od godinu dana nije pravio ovakve probleme! Na kraju cu da umem neki drugi distro (mozda fedoru), iako sam se bas vezao za mandrivu :-/
Naslov: Odg: mandriva 2008 , problem sa mreznom karticom! Poruka od: dukenukem_4d 24 Новембар 2007, 22:33:43 moglo bi ovako da se napravi ,ovaj drajver
zove funkciju is_valid_ether_addr u sledecim linijama: drivers/net/skge.c: line 2461 line 3323 line 3711 za 2.6.22 kernel,nalazi se u ovom hederu: include/linux/etherdevice.h, line 105 Kod: 96 /** 97 * is_valid_ether_addr - Determine if the given Ethernet address is valid 98 * @addr: Pointer to a six-byte array containing the Ethernet address 99 * 100 * Check that the Ethernet address (MAC) is not 00:00:00:00:00:00, is not 101 * a multicast address, and is not FF:FF:FF:FF:FF:FF. 102 * 103 * Return true if the address is valid. 104 */ 105 static inline int is_valid_ether_addr(const u8 *addr) 106 { 107 /* FF:FF:FF:FF:FF:FF is a multicast address so we don't need to 108 * explicitly check for it here. */ 109 return !is_multicast_ether_addr(addr) && !is_zero_ether_addr(addr); 110 } 111 skge.c (2.6.22) za skge 1.11 , Kod: 3322 3323 if (!is_valid_ether_addr(addr->sa_data)) 3324 return -EADDRNOTAVAIL; 3325 Kod: 2460 2461 if (!is_valid_ether_addr(dev->dev_addr)) 2462 return -EINVAL; 2463 ako se iskomentiraju ovi pozivi funkcija ali samo u redu 2461 a ovaj u redu 3323 da ostane (jer on se nalazi i u skge 1.5 ,kojoj ne smeta ,tako izgleda) (onaj u redu 3711 ,isto da ostane jer samo ispisuje u log?) i da se samo ovaj skge.c ponovo iskompilira pomocu odgovarajuceg makefile (bez rekompilacije celog kernela) ovaj u redu 2461 je u funkciji skge_up ,sto ga u stvari i sprecava da podigne interfejs O0 (ovo nije zbog linuxa ,vec zato sto je BUG u biosu ,takav da mrezna nema ispravnu MAC adresu) Naslov: Odg: mandriva 2008 , problem sa mreznom karticom! Poruka od: zchira 24 Новембар 2007, 22:44:12 to bi mogao da probam..pravi hakeraj :-)
Mada, sta mislis, da probam da flashujem bios? mozda to resi problem? Naslov: Odg: mandriva 2008 , problem sa mreznom karticom! Poruka od: dukenukem_4d 24 Новембар 2007, 22:47:14 moze i to ,ali ja sam probao jednom kod mene da stavim noviji bios asusov,
a posle sam jedva vratio ovaj stari (i od tad vise ne pipam bios ,pa sta radi -radi a sta ne radi-ne radi ) :) (na drugom ,starijem kt133 kompu je bilo uspesno doduse ,i resilo neku desetu stvar) Naslov: Odg: mandriva 2008 , problem sa mreznom karticom! Poruka od: zchira 24 Новембар 2007, 23:23:55 Pozdrav iz 2008-ice !!!!!
Ipak nisam hteo da menjam bios, sto je sigurno sigurno je (imao sam i ja losa iskustva). Promenio sam mac adresu i samo od sebe je proradilo: # ifconfig eth0 down # ifconfig eth0 hw ether 00:80:48:BA:d1:20 cak nisam ni morao da kucam 'ifconfig eth0 up' duke, hvala na pomoci i ulozenom trudu O0 Dalja pitanja, ovo verovatno moram da radim pri svakom startovanju racunara, sto znaci da treba da stavim ove 2 komande u rc.local ? Ovu adresu 00:80:48:BA:d1:20 sam stavio kao u primeru koji sam nasao na netu... jel to ima neke veze koja je? jel mogu da stavim neku drugu (recimo 00:00:00:00:00:01 ili sl...)
Powered by SMF 1.1.11 |
SMF © 2005, Simple Machines LLC |
Srpski prevod uredio: tomaja [linuxo.org]
Joomla Bridge by JoomlaHacks.com |